请老师转换代码

随心而飘

BU:=CROSS(HIGH,SAR(3,1,20));
SEL:=CROSS(SAR(3,1,20),LOW);
DRAWTEXT(BU,LOW,'B'),COLORMAGENTA,LINETHICK2;
HRATE:=IF(HIGH==LOW,1,1.01);
DRAWTEXT(SEL,HRATE*HIGH,'S'),COLORGREEN,LINETHICK2;

技术008

BU:=CROSS(HIGH,SAR(3,1,20));
SEL:=CROSS(SAR(3,1,20),LOW);
DRAWTEXT(BU,LOW,'B'),COLORMAGENTA,LINETHICK2;
HRATE:=IF(HIGH=LOW,1,1.01);
DRAWTEXT(SEL,HRATE*HIGH,'S'),COLORGREEN,LINETHICK2;

随心而飘

谢谢啦老师！下面的代码再麻烦老师转换一下

UPTJ1:=CLOSE>REF(CLOSE,1);
UPTJ2:=(CLOSE=REF(CLOSE,1) && REF(CLOSE,1)>REF(CLOSE,2));
UPTJ3:=MAX(OPEN,CLOSE)<REF(C,BARSLAST(CLOSE>REF(CLOSE,1))) AND MIN(OPEN,CLOSE)>REF(O,BARSLAST(CLOSE>REF(CLOSE,1)));
UPTJ4:=NOT (H<REF(H,1) AND L<REF(L,1));
UP:=(UPTJ1 || UPTJ2 || UPTJ3) AND UPTJ4;
DOWN:=NOT(UP);
M1:=BARSLASTCOUNT(UP);
N1:=BARSLASTCOUNT(DOWN);
CZB:=IF(M1=1 OR N1=1,2*INTPART(VOL*100/10000),INTPART(VOL*100/10000));
SZ:=IF(M1>0,SUM(CZB,M1),-1*SUM(CZB,N1));
GY:=IF(N1>0,SUM(CZB,N1),0);
XQ:=IF(M1>0,SUM(CZB,M1),0);
NOTEXT1:STICKLINE(M1>0,0,XQ,1,0),COLORRED;
NOTEXT2:STICKLINE(N1>0,0,GY,1,0),COLORGREEN;
WSB:SZ,NODRAW;

技术008

UPTJ1:=CLOSE>REF(CLOSE,1);
UPTJ2:=(CLOSE=REF(CLOSE,1) && REF(CLOSE,1)>REF(CLOSE,2));
UPTJ3:=MAX(OPEN,CLOSE)<REF(C,BARSLAST(CLOSE>REF(CLOSE,1))) AND MIN(OPEN,CLOSE)>REF(O,BARSLAST(CLOSE>REF(CLOSE,1)));
UPTJ4:=NOT (H<REF(H,1) AND L<REF(L,1));
UP:=(UPTJ1 || UPTJ2 || UPTJ3) AND UPTJ4;
DOWN:=NOT(UP);
M1:=BARSLAST(not(UP));
N1:=BARSLAST(not(DOWN));
CZB:=IF(M1=1 OR N1=1,2*INTPART(VOL*100/10000),INTPART(VOL*100/10000));
SZ:=IF(M1>0,SUM(CZB,M1),-1*SUM(CZB,N1));
GY:=IF(N1>0,SUM(CZB,N1),0);
XQ:=IF(M1>0,SUM(CZB,M1),0);
NOTEXT1:STICKLINE(M1>0,0,XQ,1,0),COLORRED;
NOTEXT2:STICKLINE(N1>0,0,GY,1,0),COLORGREEN;
WSB:SZ,NODRAW;

随心而飘

用下面的指标,麻烦老师费心编一个日内交易策略模板


VAR1:=(2*CLOSE+HIGH+LOW+OPEN)/5;
高抛: 80;
VAR2:=LLV(LOW,34);
VAR3:=HHV(HIGH,34);
SK: EMA((VAR1-VAR2)/(VAR3-VAR2)*100,13);
SD: EMA(SK,3);
低吸: 20;
强弱分界: 50;
VAR4:=IF(CROSS(SK,SD),40,22);
VAR5:=IF(CROSS(SD,SK),60,78);
卖出: VAR5;
买进: VAR4;

技术008

直接用

随心而飘

老师，我直接用了，不知为什么盘中发出的买卖信号很多很多？

技术008

那就是你条件一直在满足，这个是条件逻辑需要你自己去查看的

随心而飘

老师，但是通达信交易软件的信号很正常的

技术008

这个不清楚了，需要您自己看下的，上面代码都直接编译就能用的
也不存在函数不支持的概念